{"product_id":"faber-limestone-densifier","title":"Faber Limestone Densifier","description":"\u003cp\u003eUse The Incredible Faber Limestone Densifier water based, water repellent, non glazing limestone sealer suitable for preventing raining damp \u0026amp; aid mechanical polishing VOC free, one of the greenest limestone sealer available in Ireland it will drastically reduce the water absorption \u0026amp; avoid damp issues it will reduce drying periods when mechanically polishing the stone it will prevent dirt penetrating the stone and crating black spots high coverage area, very long lasting and suitable for indoor use Faber Limestone Densifier I Safety Information Suitable for professional use. Always follow the manufacturer's instructions and safety guidelines. Wear protective gloves, protective clothing and protective eye wear. Wash hands thoroughly after use. Store in a safe place out of reach of children. Protect Your Floor With The Faber Limestone Densifier Moisture is one of the main threats to natural stone installation, especially highly absorbent ones such as limestone. Take rising damp for instance. Here, water carries soluble salts from below the floor, and these salts recrystallize and get deposited once the water evaporates from the surface. It results in an unsightly powdery residue on the surface. Cases on damp marks on the floor caused by spills, flaking and the infamous pop-ups on your installation- these are not issues that you want affecting the surfaces in your residential or commercial premises. Treating the stone with water-repellent sealers is key, which is where products like the Faber Limestone Densifier come in. The mechanical sanding and polishing process intensifies water issues, as heat generated during grinding necessitates water for protection and lubrication, but limestone's absorbent nature complicates matters by soaking up water and prolonging drying times. This excess moisture can lead to problems like efflorescence and iron staining. The Faber Limestone Densifier has been created to improve the polishing process, minimizing time and resource usage. This is an eco-friendly formulation. The Faber Limestone Densifier is V.O.C-free, and does not pose a threat to the health of the persons applying it onto the surfaces, or those in the establishments where the floors have been treated with the product. It’s a100% water-based formulation, particularly intended for limestone and lime-based surfaces which are usually difficult to polish because of their high porosity and the water absorption capacity. What’s more, it adds to the effectiveness of the subsequent treatments that are to follow. For instance, it increases the performance of the stain-proofing treatments, thus reducing your workload when it comes to the routine cleaning and maintenance. How The Faber Limestone Densifier Works Before treating the surface with the product, the area needs to be cleaned. The dirt particles that are on the material will affect the effectiveness of the formulation. The surface should then be allowed to dry. With the polishing process: Here, the product is applied to reduce the amount of water that is absorbed by the surface, cutting down the drying time. Thus, you get to work on larger surface areas, and reduce water usage during the operations. The product itself has a 10 to 15 m2\/L coverage rate. It is applied to floors that have been sanded with the 200\/400 grain size, after which the polishing continues up to the 800 grain. At this point the required finish treatments can be applied, as opposed to the conventional modes where the polishing would have needed to be carried out to the fine grain levels of 1500 to 3000. The Faber Limestone Densifier thus enables you to get to the finishing stage much faster, that way the floor care process takes up less time and resources. The polishing process can be undertaken with products such as Faber A2 Mix, A3 Yellow, or the Cristal Pad White Pad formulation. Before applying the Faber Limestone Densifier, dry sanding is performed, and after treatment, polishing with water should occur at least 4 hours later, preferably the next day for optimal curing. Wet sanding is an option, requiring 24 to 48 hours to dry, but applying the densifier first allows for normal procedures and quicker drying after using a 200-400 grain size, after which the product should be reapplied. Protective properties of the Faber Limestone Densifier Since it is a hardening sealer, this formulation increases the ability of the surface to resist everyday scratches and abrasion, thus enhancing the durability of your installation. The water-repellent properties prevent the issues that would have arisen due to excessive moisture being absorbed by the natural stone. It achieves this without affecting the breathability, or even altering the colour of the natural stone installation. The treatment can be done on the limestone slabs and tiles before installation, as directed in these approaches: It can be at the industrial production line, or at the building where the slabs are to be set up. For the\u003c\/p\u003e","brand":"Faber","offers":[{"title":"Default Title","offer_id":47349756264636,"sku":"020200205","price":129.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0793\/8008\/6972\/files\/image_9__2nd.jpg?v=1788032563","url":"https:\/\/palcle.com\/products\/faber-limestone-densifier","provider":"PRO-MAX US","version":"1.0","type":"link"}